Concord Privacy Screen

Important Safety Notes:

• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
• We recommend an area approximately 5' x 8' for unobstructed assembling.
• You should not need to use excessive force when assembling components.

Returns:
If you wish to return your product, please contact us first — we can often help resolve the issue right away.
If a return is still necessary, it must be initiated with the retailer where the product was purchased.

If you need replacement parts, assembly assistance, or have questions about the product, our customer service team is ready to help:

• Website: https://parts.nychbrands.com
• Email: support@encloscreens.com
• Phone: 704-892-5222 or 877-234-6196

Customer service agents are available 9am–5pm EST, Monday–Friday.

For Quick Assistance:

• Have reference item number EC18022
• Provide the specific part name
• Include the batch lot number found on the end of the box

A- Spacer (18)

⅞" x 1⅛" x ⅝"

B- Post Bridge (2)

⅞" x 1⅛" x 5½"

C- Post Cap (2)

D- Joiner Clip (2)

E- Right Post Top (1)

1¼" x 1¼" x 24⅛"

F- Left Post Top (1)

1¼" x 1¼" x 24⅛"

G- Right Post Bottom (1)

1¼" x 1¼" x 36⅜"

H- Left Post Bottom (1)

1¼" x 1¼" x 36⅜"

I- Ground Stake (2)

⅞" x 1⅛" x 21½"

J- Wood Board (11)

⅝" x 4½" x 38¼"

K- Wood Block (1)

L- Wood Spacer (2)

⅝" x 1¼" x 3⅞"

M- 1" Screw (12)

Self-Drilling Stainless Steel

N- ½" Screw (8)

Stainless Steel

O- ⅛" Drill Bit (1)

J × 1

• Assemble on a box or smooth surface to prevent scratching.

H × 1

G × 1

J × 1

• Align board channel with post fin

I × 2

• Align holes

• Note: If you cannot find ground stakes, check inside posts

M × 4

L × 2

• Use Wood Spacers (L) to position the board as shown

A × 2

J × 1

• Lay panel against a wall for an easier assembly.
• Align as shown.

A × 8

J × 4

M × 2

• Attempt to push the unit into the ground. All 13½" of the ground stakes should be inserted so no longer visible.

• If ground is too hard, tap posts using a hammer. Use Wood Block (K) to avoid striking the post directly.

• If your ground is still too hard to push your screen in, either water the ground to soften it and loosen with a claw hammer, or use a tulip auger to drill holes into the ground.

• If your ground is really hard, you may need to dig a hole large enough to accommodate one post from each panel- approximately 8" in diameter and 13" deep. Backfill and compact the dirt.

A × 2

J × 1

• Repeat the previous steps to install any additional panels you purchased

• Use loose spacer to set height of board

B × 2

• Align the Post Bridges (B) with the wood board

N × 4

O × 1 (optional)

• Remove spacers once the board is secured.

If Hole is Blocked

• If rear hole is blocked, either leave off screw or pre-drill new hole as shown with the included Drill Bit (O)

F × 1

E × 1

N × 4

A × 8

J × 4

• Align as shown

M × 4

90° Angle:

180° Angle:

• Joiner clip holes do not come pre-drilled to provide flexibility when installing.
• Drill holes at your chosen locations with the included drill bill.

C × 2

• Email: support@encloscreens.com
• Phone: 704-892-5222 or 877-234-6196
• Text: 980-580-6508