4ft Florence Planter Box

Important Safety Notes:

• Check the inside of the larger pieces in your box for other materials packed inside.
• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
• We recommend an area approximately 5' x 8' for unobstructed assembling.
• You should not need to use excessive force when assembling components.

Returns:
If you wish to return your product, please contact us first — we can often help resolve the issue right away.
If a return is still necessary, it must be initiated with the retailer where the product was purchased.

Need Help or Replacement Parts?

If you need replacement parts, assembly assistance, or have questions about the product, our customer service team is ready to help:

• Website: https://parts.nychbrands.com
• Email: support@encloscreens.com
• Phone: 704-892-5222 or 877-234-6196

Customer service agents are available 9am–5pm EST, Monday–Friday.

For Quick Assistance:

• Have reference item number EC18006/EC18007
• Provide the specific part name
• Include the batch lot number found on the end of the box

• Planter Box Depth is 8 5/8" when floor is installed
• Planter Box Volume is 1.6 cu.ft.

Optional But Recommended to Avoid Tipping

• Recommended for high wind environments
• Surface mounting screws not included

Dirt:

• ¾" Rebar (2)
• Hammer

Deck:

• Power Drill
• Wood Drill Bit
• ¼" Lag Screws 3" Length (4)
• Matching Driver Bit

Patio:

• Hammer Drill
• Concrete Drill Bit
• ¼" Concrete Screws 2¼" Length (4)
• Matching Driver Bit

A — Long Board (2)

⅞" x 11" x 44"

B — Short Board (2)

⅞" x 11" x 7¼"

C — Floor Board (1)

⅞" x 7¼" x 44"

D — Long Floor Support (2)

⅞" x 1½" x 29½"

E — Thin Horizontal Slat (8)

⅞" x 1½" x 44"

F — Wide Horizontal Slat (4)

⅞" x 3" x 44"

G — Right Post (1)

1¾" x 1¾" x 44"

H — Left Post (1)

1¾" x 1¾" x 44"

I — Spacer (24)

J — Short Floor Support (3)

⅞" x 1½" x 7¼"

K — Short Post (2)

1¾" x 1¾" x 11"

L — 1½" Self-Drilling Stainless Steel Screw (8)

M — ¾" Self-Drilling Stainless Steel Screw (22)

N — Corner Post Cap (4)

O — Galvanized Steel L Bracket (2)

P — ⅛" Drill Bit (1)

A × 1

• Assemble on box or other smooth surface to prevent scratching.
• Place board with channel facing up.

D × 1

• Shift part (D) until spacing is equal on either side.

L × 4

• Ensure that the side of part (A) and part (D) are flush.

A × 1

D × 1

L × 4

• Repeat steps 1–4 to create one additional panel.

K × 2

• Ensure capped end of post faces down as shown.
• Ensure tabs on posts and notches on boards align.

M × 4

• Flip panel.

B × 2

• Lift panel.

M × 4

-Ensure that boards are flush.

H × 1

G × 1

• Open channels should be facing each other.

M × 4

• Ensure posts are flush.

A × 1

M × 4

• Ensure board is flush.

J × 4

• Align short floor supports with long floor supports.

C × 1

• Note: For best plant growth, it is recommended to drill (2) ¾" diameter drainage holes in part (C) roughly 12" apart.

I × 2

• Align tab with notch on spacer.

E × 1

E × 7

F × 4

I × 22

• Repeat steps 16 and 17, following the pattern shown above.

M × 2

N × 4

Optional But Recommended to Avoid Tipping

• Recommended for high wind environments
• Surface mounting screws not included

Dirt:

• ¾" Rebar (2)
• Hammer

Deck:

• Power Drill
• Wood Drill Bit
• ¼" Lag Screws 3" Length (4)
• Matching Driver Bit

Patio:

• Hammer Drill
• Concrete Drill Bit
• ¼" Concrete Screws 2¼" Length (4)
• Matching Driver Bit

• Recommended if installing into high wind environment.

• Recommended if installing into high wind environment.
• Surface mounting screws not included.

• Re-install removed screw.

• Drill and install mounting screws according to instructions on screw packaging.

• Repeat steps for left post.

• Email: support@encloscreens.com
• Phone: 704-892-5222 or 877-234-6196
• Text: 980-580-6508